Tuesday, June 30, 2009

Harley Davidson New Rear CAM Roller Bearing Assembly Service Bulletin


This service bulletin will guide you to remove and install the New Rear CAM roller bearing assembly on Harley Davidson motorcycle. Cam bearings may be a loose fit in the cam support plate. To avoid possible damage, be aware that camshaft and bearing assemblies may drop out at start of press procedure. Press out camshafts and bearings following existing service procedures. Regardless of model, see page 3- 83 of the 2000 FLT Models Service Manual, CAMSHAFTS/ CAMSHAFT BEARINGS, REMOVAL, steps 1-8. If reusing a rear camshaft that has the new style roller bearing installed, remove the bearing inner race and thrust washer as follows: Position WEDGE ATTACHMENT (HD-95637-46A) on inboard side of thrust washer and turn hex nuts an equal number of turns to draw halves of wedge together. Slide one bolt into channel on each side of bridge, so that flat washer is between bridge and bolt head. Thread bolts into wedge attachment an equal number of turns. Fit hardened plug into end of camshaft. Thread forcing screw into bridge until the steel ball at end of screw makes firm contact with cup of hardened plug. Verify that the tool assembly is square.
dowload:http://harley.wolfcrews.com/bulletin/m1097_TC-88_cam_bearing_service_bulletin.pdf

2008 Honda CR-V Engine Block Heater Installation Instruction



Tools and Supplies Required: Phillips screwdriver, Flat-tip screwdriver, Ratchet, 10 mm and 24 mm Sockets, Torque wrench, Diagonal cutters, Heavy gloves, Drain pan, Tape measure, White marker, Coolant (Honda All-Season Antifreeze/Coolant Type 2), Blanket
Drill, 3 mm and 7 mm Drill bits, 10 mm Hex wrench, Pushpin, Fender cover. Installation Procedures: Always use Honda All-Season Antifreeze/Coolant Type 2. Using a non-Honda coolant can result in corrosion, causing the cooling system to malfunction or fail. To avoid burning out the element, do not operate the engine block heater before it is installed in the vehicle and before you add coolant. The information in this installation instruction is intended for use only by skilled technicians who have the proper tools, equipment, and training to correctly and safely add equipment to your vehicle. These procedures should not be attempted by
“do-it-yourselfers.” Make sure you have the anti-theft codes for the radio and navigation system (if equipped), then write down
the radio presets. Open the hood, and allow the engine and all cooling system components to cool down. Disconnect the negative (-) cable from the battery, open the positive cable cover, and disconnect the positive (+) cable and clip from the battery. Unfasten
the two battery holder nuts, and remove the battery holder.

dowload:http://www.bernardiparts.com/Images/Install/2008_CRV_EngineBlockHeater_AII37479.pdf

Friday, June 26, 2009

Toyota MR2 Spider Technical Training - Manual Transmissions & Transaxles


1. Identify the purpose and function of the sequential manual transmission 2. Identify and describe the operation of the following sequential manual transmission components: a. Hydraulic Power Unit b. Gear Shift Actuator c. Shift lever d. Shift Lever Switches e. Transmission Control ECU f. ECM. Describe diagnostic equipment and tests for sequential manual transmissions, including: a. Diagnostic Tester b. Pinpoint Tests c. ECU Relearning The sequential manual transmission is based on the C Series five speed manual transaxle, and was introduced on the 2002 MR2 Spyder. The clutch pedal and master cylinder have been replaced with an actuator that is electronically controlled. Sequential Manual Transmission System Components. The transmission control ECU controls the pump assembly and the actuator assembly to engage or disengage the clutch and shift the gears. The Hydraulic Power Unit assembly generates hydraulic pressure for the shift operating system and the clutch release cylinder. Stroke Sensors : The gear shift actuator houses three sensors that monitor the shift stroke and select stroke of the shift and select lever shaft assembly, and the clutch stroke. The sequential manual transmission uses a control by wire type shift lever. The shift position and the movement of the shift lever are detected through the combination of the four switches that are integrated in the shift lever position sensor.

link dowload:http://dutch.northwestmr2.com/Toyota/mr2%20spyder/References/Technical%20Training/02%20-%20Chassis%20and%20Drivetrain/17.pdf

BMW ZF-5HP-19 Transmission Technical Service Manual



This transmission is manufactured in Germany by ZF and carries the designation ZF-5HP-19. The ZF-5HP-19 Series is an electronically controlled, five speed automatic transmission with a lock-up clutch type torque converter. Two planetary gear sets, one Ravingneaux gear set and one standard planetary gear set on the output side, four rotating multiple disc clutches, three multiple disc brake clutches, and one sprag clutch (Freewheel) are used to provide the five forward speeds and reverse. The transmission found in BMW 97-Current, 3 Series E46, 5 Series E39, 7 Series E38. Audi 95-Current, A4, A8, Audi 97-Current, A6,
Porsche Boxter 1996-1997 VW Passat 96-Current. Standard versions have a shift quadrant using only the left gate as shown above. The versions that are equipped with One-Touch Control, supplied as an option and model dependent, have a two section shift
quadrant, also shown above. Positions P, R, N, D, 4, 3, 2, can be selected in the left-hand gate and all shifts are automatic depending on which selection was made. When the selector lever is placed in the right-hand gate, the transmission can be up-shifted manually, by tapping the lever in the direction of the “Plus” symbol, or down-shifted manually by tapping the lever in the direction of the “Minus” symbol. The seperate program switch is no longer needed, as functions A and B have replaced it. If the speed of the accelerator pedal movement is greatly varied, the shift points are modified for maximum fuel economy, or a more sporting driving style accordingly. There are three shift patterns for this purpose. When a system fault is detected which could impair normal reliable operation, the ECU module interrupts the power supply to Pin 12 at the transmission case connector. The ECU module also alerts the driver of any faults by signaling the vehicles “check control” system.

link dowload:http://www.europeantransmissions.com/Bulletin/DTC.VW/00-39.pdf

# Canon EOS D30 Digital Camera Operating Steps and Reference Guides

The user’s and operation manual for Canon EOS D30 Digital Camera, contain information about : Prepare your camera for use, Start taking pictures, Check your pictures, Software Starter Guide, Connect your camera to a computer, Lens Electrical Contacts
After removing a lens from the EOS D30, set the lens with its mounting side facing up, and attach the dust cap to prevent damage to the electrical contacts and lens surface. Charge the battery pack Connect the power cord to the adapter, then attach the battery. When the charge lamp stops blinking and stays lit, the battery is completely charged. A full battery charge takes approximately 90 minutes. Insert the battery pack. Open the battery chamber cover and slide the battery pack into position
until it locks into place. Press the cover closed until it clicks shut. To check other images you have taken, see “Check the
Image Immediately” (¡44) and “Viewing Recorded Images” In this manual, the [C.Fn] symbol indicates a brief explanation of the respective custom function. For details, refer to “Custom Function Settings. The procedures in this user’s guide use a Canon EF 24-85mm F3.5-4.5 USM lens for reference. The Canon EOS D30 uses menu functions to set functions such as the quality, the date and time, and Custom Function settings. To use the menu functions, look at the LCD monitor and use the ?MENU? button,dial and button as shown below.

link dowload:http://www.usa.canon.com/app/pdf/d_eos/D30_Hardware.pdf

Canon EOS D60 Digital Camera Operation Manual

The EOS D60 digital camera is a high-performance, single-lens reflex AF camera with an ultra-fine CMOS sensor having approx. 6.3 million effective pixels. The camera is compatible with all Canon EF lenses and designed for quick and easy shooting. It is full-featured for all types of photography, from fully automatic snapshooting to professional-level, creative work. CompactFlash cards (CF Type I and II) serve as the recording medium. This is complete operation manual of the Canon EOS D60 Digital camera. The information that covered on this book are :

1. Introductions : Equipment Check List, Handling Precautions,Quick Guide, Nomenclature.

2. Before You Start : this chapters explain the basic operation before you use this digital camera. Charging the Battery Pack, Mounting and Detaching a Lens, Installing a CF Card , Basic Operation, Setting the Date and Time.

3. Single Picture Taking : explain about camera mode while you taking the pictures such as : Fully Automatic Picture Taking, Check the Image Immediately, portrait mode, Landscape Mode etc.

4. Advanced Operations : Quality Selection, ISO Speed, AF Point Selection, Setting the White Balance, Custom White Balance Setting, Checking the Depth of Field. etc

5. Flash Photography : Using the Built-in Flash , Built-in Flash Range, Flash Sync Shutter Speed and Aperture Settings, Flash Photography with the EOS-Dedicated 550EX Speedlite, Using Non-Canon Flash Units.

6. Playing and Erasing Recorded Images : Viewing Recorded Images, Automated Playback of Recorded Images, Replacing the Date/Time Battery, List of Menu Functions, Custom Function Settings.

7. Reference : Basic Terminology, Function Availability Table, Exposure Warnings, Shutter Speed and Aperture Value Readouts, Error Code, Major Specification and more.

link dowload:http://www.wedophones.com/Manuals/CamerasAndCamcorders/Canon%20CANON%20EOS-D60%20Digital%20Camera%20SLR%20Body%20Manual.pdf

Canon EOS D30 Harware User Manual

The Canon EOS D30 is a high-quality, high-precision, digital single-lens reflex camera with a CMOS sensor that has a total pixel count of 3.25 million pixels. This camera provides a full range of imaging options and functions ideal for every photographic use, from easy, fully automatic shots for first-time users to applications for experienced photographers.

Digital Camera Operating Steps and Reference Guides, Your camera includes two manuals: the “EOS D30 Camera User’s Guide” and the “Software Starter Guide.” EOS D30 Camera User’s Guide (This Document) Prepare your camera for use, Start taking pictures, Check your pictures. Before using your camera, make sure you have all the accessories shown on this and the
following page. If any are missing, contact the store where you purchased your camera.

Introduction: Digital Camera Operating Steps and Reference Guides, Check Your Accessories, Precautions for Handling,
Quick Guide, Nomenclature, Conventions Used in This Manual.

Before You Begin: Replacing the Backup Battery, charging the battery pack, inserting and removing battery pack, mounting and detaching a lens, inserting a CF card, basic operation, dioptric adjustment in the viewfinder, holding the camera.

Simple Picture Taking: Fully automatic, Check the Image Immediately, Erasing a Recorded Image, Portrait Mode, Landscape Mode, Close-Up Mode, Sports Mode, Night Scene Mode.

Advanced Operations: Quality, selection, about ISO speed, selecting parameters, AF mode selection, Focusing point selection, focusing on an off-center subject. Problem subjects for Auto focusing, setting white balance, auto exposure bracketing, bulb exposures, mirror lookup. Flash Photography, Playing and erasing recorded images.

link dowload:http://www.usa.canon.com/app/pdf/d_eos/D30_Hardware.pdf

COSMOSWorks 2007 Tutorial Finite Element Analysis

The CosmosWorks tutorial to analyze the response of a component to an applied load. Finite element analysis is a powerful tool that allows engineers to quickly analyze and refine a design. It can be applied to problems involving vibrations, heat transfer, fluid flow, and many other areas. In this tutorial, we will point out where choices and assumptions are made that could affect the accuracy of the results. If you check the box to the right of the add-in name, then that add-in will be activated whenever SolidWorks is started. Most users will prefer to activate COSMOSWorks only when it is needed for an analysis. Click the analysis tab. From the main menu, select COSMOSWorks: Study. A study defines a specific analysis and its results. A single part file can have multiple studies associated with it. In a static analysis, we assume that that loads are applied slowly. If loads are applied almost instantaneously, then dynamic effects need to be considered. A linear static analysis assumes that the response of the structure is linear – for example, a 20-lb load produces stresses and deflections that are exactly twice that of a 10-lb load. Boundary Conditions: When a component is isolated for analysis, the way in which that component is attached to another must be simulated with boundary conditions. In this case, we have chosen a fixed restraint, which means that every point on the back face of the bracket is prevented from moving in any direction. From the main menu, select COSMOSWorks: Load/Restraint: Pressure. Click on the face around the ½-inch hole as shown here. From the main menu, select COSMOSWorks: Mesh: Create. Move the slider bar toward the right (fine) and click the check mark. Mesh Size: A finer mesh, with more elements, will generally produce more accurate results at the expense of longer processing time.

link dowload:http://highered.mcgraw-hill.com/sites/dl/free/0073402443/385888/FEA_Tutorial_2007.pdf

cosmosworks introductions tutorial-design analysis made simple

Cosmosworks is a useful software for design analysis in mechanical engineering. That’s an introduction for you who would like to learn more about COSMOSWorks. COSMOSWorks is a design analysis automation application fully integrated with SolidWorks. This software uses the Finite Element Method (FEM) to simulate the working conditions of your designs and predict their behavior. FEM requires the solution of large systems of equations. Powered by fast solvers, COSMOSWorks makes it possible for designers to quickly check the integrity of their designs and search for the optimum solution. A product development cycle typically includes the following steps: 1 Build your model in the SolidWorks CAD system. 2 Prototype the design. 3 Test the prototype in the field. 4 Evaluate the results of the field tests. 5 Modify the design based on the field test results. Analysis Steps : You complete a study by performing the following steps: • Create a study defining its analysis type and options. • If needed, define parameters of your study. Parameters could be a model dimension, a material property, a force value, or any other entity that you want to investigate its impact on the design. Analysis Background: Linear Static Analysis Frequency Analysis Linearized Buckling Analysis Thermal Analysis Optimization Studies, Material property, Material Models, Linear Elastic Isotropic. Plotting Results. Describes how to generate a result plot and result tools. Listing Results. Overview of the results that can be listed. Graphing Results. Shows you how to graph results. Results of Structural Studies. Lists results available from structural studies. Results of Thermal Studies. Lists results available from thermal studies. Reports. Explains the study report utility. Stress Check. Lists the basics of checking stress results and different criteria used in the checking.

linkdowload:http://www.ebooksquad.com/2008/06/20/www.owlnet.rice.edu/~mech403/HelpFiles/IntroducingCW.pdf

autocad-2008-tutorial-2d-fundamentals

Create and Save AutoCAD drawing files ? Use the AutoCAD visual reference commands ? Draw, using the LINE and CIRCLE
commands ? Use the ERASE command ? Define Positions using the Basic Entry methods ? Use the AutoCAD Pan Realtime option. In order to become effective in using a CAD system, we must learn to create geometric entities quickly and accurately. In learning to use a CAD system, lines and circles are the first two, and perhaps the most important two, geometric entities that one should master the skills of creating and modifying. Note that AutoCAD automatically assigns generic name, Drawing X, as new drawings are created. In our example, AutoCAD opened the graphics window using the default system units and assigned the drawing name Drawing1. Drawing Units Setup Every object we construct in a CAD system is measured in units. We should determine the value of the units within the CAD system before creating the first geometric entities. Drawing Area Setup Next, we will set up the Drawing Limits; setting the Drawing Limits controls the extents of the display of the grid. It also serves as a visual reference that marks the working area. On your own, move the graphic cursor near the upper-right comer inside the drawing area and note that the drawing area is unchanged. (The Drawing Limits command is used to set the drawing area, but the display will not be adjusted until a display command is used.). Visual reference, Using the buttons is a quick and easy way to make changes to these drawing aid options. The CAD Database and the User Coordinate System.




link dowload:http://www.acaddemo.com/pdfsample/978-1-58503-361-4-1.pdf

Ebook Introducing Autodesk Inventor 2009


Link dowload :
http://rapidshare.com/files/206416620/IntrAutodeInv.zip

sion 5 Administration

CATIA Version 5 Administration
Link dowload :
http://www.tgstech.com/files/Course_Description_CAT503.pdf

CATIA Version 5 Knowledgeware

CATIA Version 5 Knowledgeware
Link dowload :
http://www.tgstech.com/files/Course_Description_CAT510.pdf

CATIA For Automotive Suppliers

CATIA For Automotive Suppliers
Link dowload :
http://www.plmlatam.com/datos/downloads/CATIA_for_Automotive_Suppliers_Brochure_LD.pdf

CATIA - Composites Design 3 (CPD)

CATIA - Composites Design 3 (CPD)
Link dowload :
http://www.catia.cz/fileadmin/Pictures_Menu/Catia/Catia_V5/Mechanical_Domain/pdf/CPD.pdf

Catia Antunes

Catia Antunes
Link dowload :
http://www.globalcarbonproject.org/global/pdf/Methane%20Hydrates_Participants.pdf

Intelligent Two Handed Power for CATIA V5

Intelligent Two Handed Power for CATIA V5
Link dowload :
http://www.3dconnexion.com/docs/ISV_Catia_ENG.pdf

Fluent For Catia

Link dowload :
http://www.fluentforcatia.com/FfC_MCAD_article_jan06.pdf

Teamcenter Integration for CATIA V5

Teamcenter Integration for CATIA V5
Link dowload :
http://www.plm.automation.siemens.com/en_us/Images/tc_integration_for_catia_fs_W2_tcm53-49242.pdf

CATIA Certified Professional Exams

Link dowload :
http://www.3ds.com/fileadmin/education/CATIACertif_SampleQuestions.pdf

CATIA PLM Express

Link dowload :
http://www.3ds.com/fileadmin/PRODUCTS/CATIA/OFFERS/CATIA-PLM-EXPRESS/PDF/CATIA-PLM-EXPRESS.pdf

Tuesday, June 16, 2009

Oracle Multimedia Software Downloads

Integration With Streaming Servers
-Plugin for Microsoft Windows Media Streaming Services
-Plugin for RealNetworks Streaming Servers on 32-bit Linux
-Plugin for RealNetworks Streaming Servers on Windows (NT/XP)

Multimedia Features
-Oracle Multimedia OraDAV Driver

Other Multimedia Features
-Oracle Multimedia Java Client 10g
-Support for the Windows Media File Format (ASF)
-Application Server 10g Multimedia Tag Library for JSP

Multimedia Downloads For Earlier Versions
-Oracle Multimedia Java Client 9i
-Code Wizard for the PL/SQL Gateway

dowload:http://www.oracle.com/technology/software/products/intermedia/index

Code-cracking and computers

By Mark Ward
Technology correspondent, BBC News

By the end of WWII, 11 Colossus machines were in use

Bletchley Park is best known for the work done on cracking the German codes and helping to bring World War II to a close far sooner than might have happened without those code breakers.

But many believe Bletchley should be celebrated not just for what it ended but also for what it started - namely the computer age.

The pioneering machines at Bletchley were created to help codebreakers cope with the enormous volume of enciphered material the Allies managed to intercept.

The machine that arguably had the greatest influence in those early days of computing was Colossus - a re-built version of which now resides in the National Museum of Computing which is also on the Bletchley site.

Men and machine

The Enigma machines were used by the field units of the German Army, Navy and Airforce. But the communications between Hitler and his generals were protected by different machines: The Lorenz SZ40 and SZ42.

The German High Command used the Lorenz machine because it was so much faster than the Enigma, making it much easier to send large amounts of text.

"For about 500 words Enigma was reasonable but for a whole report it was hopeless," said Jack Copeland, professor of philosophy at the University of Canterbury in New Zealand, director of the Turing Archive and a man with a passionate interest in the Bletchley Park computers.

Bletchley employed thousands of code breakers during wartime


The Allies first picked up the stream of enciphered traffic, dubbed Tunny, in 1940. The importance of the material it contained soon became apparent.

Like Enigma, the Lorenz machines enciphered text by mixing it with characters generated by a series of pinwheels.

"We broke wheel patterns for a whole year before Colossus came in," said Captain Jerry Roberts, one of the codebreakers who deciphered Tunny traffic at Bletchley.

"Because of the rapid expansion in the use of Tunny, our efforts were no longer enough and we had to have the machines in to do a better job."

The man who made Colossus was Post Office engineer Tommy Flowers, who had instantly impressed Alan Turing when asked by the maverick mathematician to design a machine to help him in his war work.

But, said Capt Roberts, Flowers could not have built his machine without the astonishing work of Cambridge mathematician Bill Tutte.

"I remember seeing him staring into the middle distance and twiddling his pencil and I wondered if he was earning his corn," said Capt Roberts.

But it soon became apparent that he was.

"He figured out how the Lorenz machine worked without ever having seen one and he worked out the algorithm that broke the traffic on a day-to-day basis," said Capt Roberts.

"If there had not been Bill Tutte, there would not have been any need for Tommy Flowers," he said. "The computer would have happened later. Much later."

Valve trouble

Prof Copeland said Tommy Flowers faced scepticism from Bletchley Park staff and others that his idea for a high-speed computer employing thousands of valves would ever work.

Colossus kept valves lit to ensure they kept on working

"Flowers was very much swimming against the current as valves were only being used in small units," he said. "But the idea of using large numbers of valves reliably was Tommy Flowers' big thing. He'd experimented and knew how to control the parameters."

And work it did.

The close co-operation between the human translators and the machines meant that the Allies got a close look at the intimate thoughts of the German High Command.

Information gleaned from Tunny was passed to the Russians and was instrumental in helping it defeat the Germans at Kursk - widely seen as one of the turning points of WWII.

The greater legacy is the influence of Colossus on the origins of the computer age.

"Tommy Flowers was the key figure for everything that happened subsequently in British computers," said Prof Copeland.

After the war Bletchley veterans Alan Turing and Max Newman separately did more work on computers using the basic designs and plans seen in Colossus.

Turing worked on the Automatic Computing Engine for the British government and Newman helped to bring to life the Manchester Small Scale Experimental Machine - widely acknowledged as the first stored program computer.

The work that went into Colossus also shaped the thinking of others such as Maurice Wilkes, Freddie Williams, Tom Kilburn and many others - essentially the whole cast of characters from whom early British computing arose.

And the rest, as they say, is history.

--------
BBC

Video Tutorial Mastercam 9

Link dowload :
http://www.mediafire.com/?guqiixuntc0
http://www.mediafire.com/?mxlmeia58th
http://www.mediafire.com/?z9twtibfnus
http://www.mediafire.com/?qmg5umv4byp
http://www.mediafire.com/?hjulhn5yvai
http://www.mediafire.com/?zpjwa617ml2
http://www.mediafire.com/?6rqmqjcmaao
http://www.mediafire.com/?0nzgvij88jb
http://www.mediafire.com/?3ibzupykb25
http://www.mediafire.com/?ff2jsxwclen
http://www.mediafire.com/?dcbkirve5c1
http://www.mediafire.com/?z0anlai4n5i
http://www.mediafire.com/?pbizyukdxwc
http://www.mediafire.com/?nvbv3mjgbxl

Tutorial MasterCam



Link dowload :
http://www.4shared.com/file/55698107/ca79f5a1/Tuto_Mastercam_X_-_Millpart1.html
http://www.4shared.com/file/55700592/6f208b80/Tuto_Mastercam_X_-_Millpart2.html
http://www.4shared.com/file/55702620/ca9545b5/Tuto_Mastercam_X_-_Millpart3.html
http://www.4shared.com/file/55704769/f38c0dfe/Tuto_Mastercam_X_-_Millpart4.html
http://www.4shared.com/file/55706352/e273e7e2/Tuto_Mastercam_X_-_Millpart5.html

Portable Driver Genius Pro Edition 8.0.0.316


Driver Genius Professional is a professional driver management tool features both driver management and hardware diagnostics. Driver Genius provides such practical functions as driver backup, restoration, update and removal for computer users. If you often reinstall your operating system, you may not forget such painful experiences of searching all around for all kinds of drivers. If unfortunately you have lost your driver CD, the search will be more troublesome and time-consuming.

Now with the driver backup function of Driver Genius, you can backup all drivers in your computer before reinstalling, and restore them with the driver restoration function after system reinstallation has been completed. This will dramatically save your time for driver installation during the system installation procedure, and you will no longer worry about where to find a driver. Besides, you can create an automatic installation package for all drivers in your system by Driver Genius. After you have reinstalled your operating system, you can restore all your drivers in just a click by this automatic restoration program. It's really convenient. Driver Genius can automatically find driver for a device that the system can't find a driver for it. It can recognize the name and vendor's information of the device, and directly provide download URL for the required driver. Driver Genius also supports online updates for drivers of existing hardware devices. There are more than 30,000 most recent drivers for such hardware devices as motherboards, video cards, sound cards, network cards, modems, monitors, mice, keyboards, digital cameras, video capture cards, etc. on Driver Genius web site. Besides, there are daily updates for many drivers on our site. Our customers can obtain information for latest drivers by Driver Genius's LiveUpdate program, which can synchronize to the database on our site.

Backup, restore and update all your drivers in several mouse clicks. Get new driver for your computer now!

• Quickly backup device drivers for your computer.
• Just need one click to restore all drivers.
• Clone your drivers to an EXE auto-installer. Easy to install the drivers to many machines.
• Easy to get the most recent drivers for your computer. Keep your drivers up to date.
• Remove invalid drivers and useless drivers, improve system performance and stability.
• Device Diagnostics helps you locate a device that is not working properly or efficiently and offers an effective solution.
• Unlocks many hidden options in the NVIDIA display driver control panel. Including over clocking settings, AGP settings, Fan control, Stereo control, OpenGL 2.0 support, and more.

Operating System: Windows 98/ME/2000/XP/Server 2003/Vista/x 64

Homepage - http://www.driver-soft.com

Download Portable Driver Genius Pro Edition 8.0.0.316

copyright :maxdownload4u

Portable Microsoft Office 2010 - Technical preview



Microsoft Office 2010 or Office 14 - the working title of the next version of Microsoft Office for Microsoft Windows. Microsoft started work on Office 2010 in 2006, which ended the work on the Microsoft Office 12 (which went under the name of Microsoft Office 2007).
Includes:
Word 2010, Excel 2010, PowerPoint 2010

Initially it was thought that Office 2010 will be released for sale in the first half of 2009, but the new data it is not expected before late 2009 and early 2010. It is anticipated that Office 2010 will be presented at about the same time with the new operating system Microsoft Windows 7. According to an article in InfoWorld in April 2006, Office 2010 will be a «role», than previous versions. The article quoted Simon Vittsa (eng. Simon Witts), vice-president of Microsoft's Enterprise and Partner Group, which said that the package will focus on some of the staff - researchers, developers, managers, HR. Office 2010 borrows some ideas from the ideology of «Web 2.0», and, perhaps, Microsoft SharePoint Server to build capabilities in new version of office suite.

Office 2010 implements the ISO version is compatible with Office Open XML, which has been standardized as ISO 29500 in March 2008. Microsoft also plans to provide Web-version of its Office products, known as Office Web, debuted along with Office 2010. Office Web will include online versions of Word, Excel, PowerPoint and OneNote. It was expected that the new version will be distributed free of charge, but revenues will be removed from advertising. In addition, Office 2010 will be offered in two versions - to 32-bit and 64-bit processors. Microsoft Office 2010 Technical preview will be released in late June - early July. Send it can be only by invitation. But you can apply now. However, Microsoft Office 2010 Technical Preview is already safely land in the network.

Download Portable Microsoft Office 2010 - Technical preview

http://hotfile.com/dl/6456879/dfad86b/Office_2010_Portable.part1.rar.html
http://hotfile.com/dl/6456895/3bf6048/Office_2010_Portable.part2.rar.html
http://hotfile.com/dl/6456910/0b7f73f/Office_2010_Portable.part3.rar.html
http://hotfile.com/dl/6456936/3e7ac8b/Office_2010_Portable.part4.rar.html
http://hotfile.com/dl/6456948/1c2f2d7/Office_2010_Portable.part5.rar.html
http://hotfile.com/dl/6456963/80af259/Office_2010_Portable.part6.rar.html
http://hotfile.com/dl/6456966/3001578/Office_2010_Portable.part7.rar.html

copyright :maxdownload4u

Sunday, June 14, 2009

SC Free DVD Ripper and Burner



SC Free DVD Ripper and Burner; Burn for CD, DVD burning, ripping. Data Burner - create, burn traditional data CDs, DVDs, and ISO-images as well as multi-session, bootable. Audio Burner - create, burn audio CDs easily from WAV, MP3, WMA, OGG, RAW, VOX, etc files, burn CUE-images to disc directly. Features - Record Discs by Drag, Drop data or audio information contained in files onto icons on the desktop, start automatically with windows start up, Create Discs from a DVD, best Audio or Data Discs that can be read with any PC, Supports most IDE, USB, IEEE1384, SCSI DVD+R/RW, CD recorders, Records DVD+R/RW, CD discs On-the-Fly, erases re-writable discs, Supports Buffer Protection systems, Burn Proof, others error free recording types, Creates fully compatible ISO9660 Level 1, 2, Joliet data CDs, DVDs, Imports multi-session CDs, DVDs, merges new files with an existing session, Detects drive(s) type(s), prevents you from trying to record a DVD on a CD-RW recorder, Allows fast ripping from audio CDs to WAV, MP3, WMA or OGG formats directly without intermediate WAV files using your own codec presets, Gets CDDB information for audio CDs, Supports jitter-correction ripping modes to restore damaged tracks from scratched CDs. ASPI is not required for NT/2000/XP.

link dowload:http://rutgon.com/118

Fast DVD Converter 5.8




Fast DVD Converter 5.8

"Powerful tool that lets you convert DVD to VCD, SVCD, AVI, DivX, XviD formats."

Fast DVD Converter is a powerful and easy-to-use software that lets you convert DVD to VCD,
SVCD, AVI, DivX, and XviD formats. You are able to Extract or convert DVD audio to WAV,
and MP3 formats with defining ID3 tag which is playable on any Portable Mp3 player.

It provides a preview function before converting even for each title or chapter. You may set
up a batch of files and convert them in a single operation. Split output file to specified size,
select language tracks and subtitles.

Make backup copies of your favorite DVD without any loss of quality. Ability to convert
selected titles or chapters instead of whole movie, with its own settings, independent of the
others. you can free download Fast DVD Converter 5.8 now.



dowload: http://www.armenian-dictionary.com/download/other/FastDVDSetup.exe

AutoCAD 2009




Design and shape the world around you with the powerful, flexible features found in AutoCAD® design and documentation software, one of the world’s leading 2D and 3D CAD tools. Speed documentation, share ideas seamlessly, and explore ideas more intuitively in 3D. With thousands of available add-ons, AutoCAD software provides the ultimate in flexibility, customized for your specific needs. It’s time to take design further. It’s time for AutoCAD.

dowload trial:http://download.softpedia.com/dl/3167009424a913f24f277dec8b8e4042/48d31c49/100104603/software/science/AutoCAD_2009_English_Win_32bit.exe

Thursday, June 4, 2009

SolidWorks Video Tutorial 4th Edition

Link dowload :
http://rapidshare.com/files/20669633...tdk.part01.rar
http://rapidshare.com/files/20669642...tdk.part02.rar
http://rapidshare.com/files/20669632...tdk.part03.rar
http://rapidshare.com/files/20669635...tdk.part04.rar
http://rapidshare.com/files/20669641...tdk.part05.rar
http://rapidshare.com/files/20669642...tdk.part06.rar
http://rapidshare.com/files/20669641...tdk.part07.rar
http://rapidshare.com/files/20669638...tdk.part08.rar
http://rapidshare.com/files/20669643...tdk.part09.rar
http://rapidshare.com/files/20669634...tdk.part10.rar
http://rapidshare.com/files/20669618...tdk.part11.rar
http://rapidshare.com/files/20669615...tdk.part12.rar
http://rapidshare.com/files/20669629...tdk.part13.rar
http://rapidshare.com/files/20669605...tdk.part14.rar
http://rapidshare.com/files/20669610...tdk.part15.rar
http://rapidshare.com/files/20669632...tdk.part16.rar
http://rapidshare.com/files/20669646...tdk.part17.rar
http://rapidshare.com/files/20669639...tdk.part18.rar
http://rapidshare.com/files/20669645...tdk.part19.rar
http://rapidshare.com/files/20669632...tdk.part20.rar
http://rapidshare.com/files/20669634...tdk.part21.rar
http://rapidshare.com/files/20669634...tdk.part22.rar
http://rapidshare.com/files/20669632...tdk.part23.rar
http://rapidshare.com/files/20669634...tdk.part24.rar
http://rapidshare.com/files/20669635...tdk.part25.rar
http://rapidshare.com/files/20669630...tdk.part26.rar
http://rapidshare.com/files/20669624...tdk.part27.rar
http://rapidshare.com/files/20669594...tdk.part28.rar

Tutorial Solidworks 2003

Link Dowload :

http://www.mkn.itu.edu.tr/~mkimrak/Solidworks2003.pdf